SIPLUS extreme RAIL analog input modules

Заказные данные
(2)
Аксессуары
(5)

4-channel analog input (AI) modules
Approved in accordance with the EN 50155, EN 15121, EN 50124, EN 50125 and EN 45545 railway standards for use in rail traffic

For different requirements, the digital output modules offer:

BaseUnits for single or multiple-conductor connection with automatic slot coding
Individual system-integrated load group formation with self-assembling voltage distribution bars (a separate power module is no longer required for ET 200SP)
Option of connecting current, voltage and resistance sensors, as well as thermocouples
Energy Meter for recording up to 200 electrical variables
Clear labeling on front of module
LEDs for diagnostics, status, supply voltage and faults
Electronically readable and non-volatile writable rating plate (I&M data 0 to 3)
Optional accessories
- Labeling strips (film or card)
- Equipment labeling plate
- Color-coded label with module-specific CC Code
- Shielding terminal

A quick and clear comparison of the functions of the AI modules is offered by the TIA Selection Tool.

Overview of analog input modules

Analog input	PU	Article No.	CC-Code	BU type
AI 4 x I 2/4-wire ST	1	6AG2134-6GD00-4BA1	CC03	A0, A1
AI Energy Meter ST	1	6AG2134-6PA00-4BD0	CC00	D0

Overview of BaseUnits

BaseUnit	PU	Article No.	CC-Codes for process terminals	CC-Codes for AUX terminals
BU type A0 New load group (light) 16 process terminals With 10 AUX terminals	1	6AG2193-6BP20-4DA0	CC01 to CC05	CC71 to CC73
BU type A0 New load group (light) 16 process terminals Without AUX terminals	1	6AG2193-6BP00-4DA0	CC01 to CC05	--
BU type A0 Forwarding of load group (dark) 16 process terminals With 10 AUX terminals	1	6AG2193-6BP20-4BA0	CC01 to CC05	CC71 to CC73
BU type A0 Forwarding of load group (dark) 16 process terminals Without AUX terminals	1	6AG2193-6BP00-4BA0	CC01 to CC05	--
BU type D0 Forwarding of load group (dark) 12 process terminals Without AUX terminals	1	6AG2193-6BP00-4BD0	--	--

Область применения

The measured values of analog sensors (current, voltage, resistance, temperature etc.) can be recorded and transferred to the higher-level controller via the analog input modules.

Дизайн

Usable BaseUnits (BU)

BaseUnits with an appropriate number of terminals are available for single or multi-conductor connection.

All variants that correspond to the BU type of the I/O module used can be used as BaseUnits (see Selection and ordering data).

Load group formation

A light-colored BU separates the self-assembling, internal voltage buses (P1, P2, AUX) and thus opens a new load group. The supply voltage of a load group must be fed in at the light BU of this load group.

A dark BU forwards the supply voltage of the adjacent light BU on the left via the self-assembling voltage buses P1, P2 and AUX. A new infeed is therefore only required on the next light BU to the right. The setting of a further light BU is required whenever

a new load group is to be formed (for example, for isolating the supply voltage from module groups) or
the maximum current simultaneously required by the load group exceeds the permissible limit of 10 A.

Color identification of the terminals

The potentials at the terminals of the BaseUnit are defined by the inserted I/O module in each case. To prevent wiring faults, the potentials of the terminals can optionally be identified by means of module-specific color-coded labels. The color-coded label that matches the respective I/O module is defined by the color code CCxx of the I/O module. This color code is also printed on the front of the module.

In BaseUnits with the additional ten internally jumpered AUX terminals or 2x5 additional terminals, these can also be identified with color-coded labels. For the ten AUX terminals, color-coded labels are available in red, blue, and yellow/green.

Labeling

Labeling strips

Labeling strips can be inserted on the front of the interface modules or I/O modules and individually labeled by means of STEP7, macros, etc. No special additional holder is required. If required, they can be easily replaced with the component.

Equipment labeling plates

Equipment labeling plates enable the equipment to be easily identified (e.g. compliant with EN 81346). They are easily plugged onto the required component (interface modules, I/O modules and BaseUnits) and when required, they can be easily replaced with the component.

The following labeling components are available:

Film labeling strips, light-gray, roll with 500 strips, perforated, for thermal transfer printers

Film labeling strips, yellow, roll with 500 strips, perforated, for thermal transfer printers
Card labeling strips (180 g/m²), light gray, DIN A4 sheets with 100 strips each, perforated, for laser printer
Card labeling strips (180 g/m²), yellow, DIN A4 sheets with 100 strips each, perforated, for laser printer
Equipment labeling plates, white, ten sheets each with 16 labels, for thermal transfer card printers or labels

System-integrated shielded connection

For the space-saving and EMC-optimized connection of cable shields, a shield connection is available that is quick and easy to mount. This consists of one shield connection element that can be plugged onto the BaseUnit and one shield terminal for each module. The low-impedance connection to the functional ground (DIN rail) is achieved without any additional wiring by the user.

Технические данные

Order number		6AG2134-6GD00-4BA1
		SIPLUS ET 200SP AI 4XI 2-/4-WIRE TX RAIL
General information
Product type designation		AI 4xI 2-/4-wire ST
Product function
● I&M data		Yes; I&M0 to I&M3
● Measuring range scalable		No
Operating mode
● Oversampling		No
● MSI		No
CiR – Configuration in RUN
Reparameterization possible in RUN		Yes
Calibration possible in RUN		No
Supply voltage
Type of supply voltage		DC
Rated value (DC)		24 V
Reverse polarity protection		Yes
Analog inputs
Number of analog inputs		4; > 60 °C max. 1x +/- 20 mA permissible
permissible input current for current input (destruction limit), max.		50 mA
Cycle time (all channels), min.		Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels)
Input ranges (rated values), currents
● 0 to 20 mA		Yes
● -20 mA to +20 mA		Yes
● 4 mA to 20 mA		Yes
Cable length
● shielded, max.		1 000 m
Analog value generation for the inputs
Integration and conversion time/resolution per channel
● Resolution with overrange (bit including sign), max.		16 bit
● Integration time, parameterizable		Yes
● Interference voltage suppression for interference frequency f1 in Hz		16.6 / 50 / 60 Hz
● Conversion time (per channel)		180 / 60 / 50 ms
Smoothing of measured values
● Number of smoothing levels		4; None; 4/8/16 times
● parameterizable		Yes
Encoder
Connection of signal encoders
● for voltage measurement		No
● for current measurement as 2-wire transducer		Yes
— Burden of 2-wire transmitter, max.		650 Ω
● for current measurement as 4-wire transducer		Yes
Errors/accuracies
Basic error limit (operational limit at 25 °C)
● Current, relative to input range, (+/-)		0.3 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
● Series mode interference (peak value of interference < rated value of input range), min.		70 dB
● Common mode voltage, max.		10 V
● Common mode interference, min.		90 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)		No
Interrupts/diagnostics/status information
Diagnostics function		Yes
Alarms
● Diagnostic alarm		Yes
● Limit value alarm		No
Diagnostic messages
● Monitoring the supply voltage		Yes
● Wire-break		Yes; at 4 to 20 mA
● Short-circuit		Yes; 2-wire mode: Short-circuit of the encoder supply to ground or of an input to the encoder supply
● Group error		Yes
● Overflow/underflow		Yes
Diagnostics indication LED
● Monitoring of the supply voltage (PWR-LED)		Yes; Green LED
● Channel status display		Yes; Green LED
● for channel diagnostics		No
● for module diagnostics		Yes; Green/red LED
Potential separation
Potential separation channels
● between the channels and backplane bus		Yes
Isolation
Isolation tested with		707 V DC (type test) and according to EN 50155 (routine test)
Standards, approvals, certificates
Railway application
● EN 50121-3-2		Yes; EMC for rail vehicles
● EN 50121-4		Yes; EMC for signal and telecommunications systems
● EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
● EN 50125-1		Yes; Rail vehicles - see ambient conditions
● EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions
● EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
● EN 50155		Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2
● EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
● Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.		-40 °C; = Tmin
● horizontal installation, max.		70 °C; = Tmax; +85 °C for 10 min (Tx acc. to EN 50155)
Extended ambient conditions
● relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
Dimensions
Width		15 mm
Weights
Weight, approx.		31 g
Other
Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776

Order number		6AG2134-6PA00-4BD0
		SIPLUS ET 200SP AI ENERGY METER TX RAIL
General information
Product type designation		AI energy meter 400VAC ST
Product function
● Voltage measurement		Yes
● Voltage measurement with voltage transformers		No
● Current measurement		Yes
● Phase current measurement without current transformers		No
● Phase current measurement with current transformers		Yes
● Energy measurement		Yes
● Frequency measurement		Yes
● Power measurement		Yes
● Active power measurement		Yes
● Reactive power measurement		Yes
● I&M data		Yes; I&M0 to I&M3
● Isochronous mode		No
Operating mode
● cyclic measurement		Yes
● acyclic measurement		Yes
● Acyclic measured value access		Yes
● Fixed measured value sets		Yes
● Freely definable measured value sets		No
CiR – Configuration in RUN
Reparameterization possible in RUN		Yes
Calibration possible in RUN		No
Installation type/mounting
Mounting position		Horizontal
Supply voltage
Design of the power supply		Supply via voltage measurement channel L1
Type of supply voltage		100 - 240 V AC
permissible range, lower limit (AC)		90 V
permissible range, upper limit (AC)		264 V
Line frequency
● permissible range, lower limit		47 Hz
● permissible range, upper limit		63 Hz
Address area
Address space per module
● Address space per module, max.		44 byte; 32 byte input / 12 byte output
Analog inputs
Cycle time (all channels), typ.		50 ms; Time for consistent update of all measured and calculated values (cyclic und acyclic data)
Interrupts/diagnostics/status information
Alarms
● Diagnostic alarm		Yes
● Limit value alarm		No
● Hardware interrupt		No
Diagnostics indication LED
● Monitoring of the supply voltage (PWR-LED)		Yes
● Channel status display		Yes; Green LED
● for channel diagnostics		Yes; red Fn LED
● for module diagnostics		Yes; green/red DIAG LED
Integrated Functions
Measuring functions
● Measuring procedure for voltage measurement		TRMS
● Measuring procedure for current measurement		TRMS
● Type of measured value acquisition		seamless
● Curve shape of voltage		Sinusoidal or distorted
● Buffering of measured variables		No
● Parameter length		38 byte
● Bandwidth of measured value acquisition		2 kHz; Harmonics: 39 / 50 Hz, 32 / 60 Hz
Operating mode for measured value acquisition
— automatic detection of line frequency		No; Parameterizable
Measuring range
— Frequency measurement, min.		45 Hz
— Frequency measurement, max.		65 Hz
Measuring inputs for voltage
— Measurable line voltage between phase and neutral conductor		230 V
— Measurable line voltage between the line conductors		400 V
— Measurable line voltage between phase and neutral conductor, min.		90 V
— Measurable line voltage between phase and neutral conductor, max.		264 V
— Measurable line voltage between the line conductors, min.		155 V
— Measurable line voltage between the line conductors, max.		460 V
— Measurement category for voltage measurement in accordance with IEC 61010-2-030		CAT II; CAT III in case of guaranteed protection level of 1.5 kV
— Internal resistance line conductor and neutral conductor		3.4 MΩ
— Power consumption per phase		20 mW
— Impulse voltage resistance 1,2/50µs		1 kV
Measuring inputs for current
— measurable relative current (AC), min.		5 %; Relative to the secondary rated current; 1 A, 5 A
— measurable relative current (AC), max.		100 %; Relative to the secondary rated current; 1 A, 5 A
— Continuous current with AC, maximum permissible		5 A; at > +60 °C max. permissible current 1 A per phase
— Apparent power consumption per phase for measuring range 5 A		0.6 V·A
— Rated value short-time withstand current restricted to 1 s		100 A
— Input resistance measuring range 0 to 5 A		25 mΩ
— Zero point suppression		Parameterizable: 20 - 250 mA, default 50 mA
— Surge strength		10 A; for 1 minute
Accuracy class according to IEC 61557-12
— Measured variable voltage		0.5
— Measured variable current		0.5
— Measured variable apparent power		1
— Measured variable active power		1
— Measured variable reactive power		1
— Measured variable power factor		0.5
— Measured variable active energy		1
— Measured variable reactive energy		2
— Measured variable phase angle		±1 °; not covered by IEC 61557-12
— Measured variable frequency		0.05
Potential separation
Potential separation channels
● between the channels and backplane bus		Yes; 3 700V AC (type test) CAT III
Isolation
Isolation tested with		2 300 V AC for 1 minute (type test) and according to EN 50155 (routine test)
Standards, approvals, certificates
Railway application
● EN 50121-3-2		Yes; EMC for rail vehicles
● EN 50121-4		Yes; EMC for signal and telecommunications systems
● EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
● EN 50125-1		Yes; Rail vehicles - see ambient conditions
● EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions
● EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
● EN 50155		Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2
● EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
● Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.		-40 °C; = Tmin
● horizontal installation, max.		70 °C; = Tmax; +85 °C for 10 min (Tx acc. to EN 50155)
Extended ambient conditions
● relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
Dimensions
Width		20 mm
Weights
Weight (without packaging)		45 g
Other
Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776
Data for selecting a current transformer
● Burden power current transformer x/1A, min.		As a function of cable length and cross section, see device manual
● Burden power current transformer x/5A, min.		As a function of cable length and cross section, see device manual