1-phase, 24 V DC (for S7-1500 and ET200MP)

• Заказные данные
  (2)
• Аксессуары
  (1)
• Информационные материалы

  Информационные материалы

  The design and functionality of the SIMATIC PM 1507 single-phase load power supply (PM = power module) with automatic range selection of the input voltage makes it an optimal match to the SIMATIC S7-1500 PLC. It supplies the S7-1500 system components such as CPU, system power supply (PS), I/O circuits of the input and output modules and, if necessary, the sensors and actuators with 24 V DC.

  Дизайн

  • The load current supplies are directly fastened to the S7-1500 mounting rail (without connection to the backplane bus) and can be mounted directly to the left of the CPU (no installation clearance required)
  • Diagnostics LEDs to indicate status and faults: Operation, Fault, Stand-by
  • ON/OFF switches (operation/stand-by) in case of swapping modules
  • Mains connection plug with touch protection and strain relief for connection of input voltage (enables permanent wiring)
  • Plug-in 24 V DC output terminal with reverse polarity protection for connection of 24 V loads (enables permanent wiring)

  Функции

  • Connection to all 1-phase 50/60 Hz networks (120 / 230 V AC) through automatic range switching
  • Short-term mains buffering
  • Output voltage of 24 V DC that is limited to maximum 28 V DC (prevents any damages in 24 V loads if input voltage is too high)
  • 50% "Extra Power" for 5 seconds per minute for short-term overloads, for example, when switching on 24V consumers

  Технические данные

  Order number		6EP1332-4BA00	6EP1333-4BA00
  Product		S7-1500 PM1507	S7-1500 PM1507
  Power supply, type		24 V/3 A	24 V/8 A
  Input
  Input		1-phase AC	1-phase AC
  Supply voltage
  ● 1 at AC Rated value		120 V	120 V
  ● 2 at AC Rated value		230 V	230 V
  ● Note		Automatic range selection	Automatic range selection
  Input voltage
  ● 1 at AC		85 ... 132 V	85 ... 132 V
  ● 2 at AC		170 ... 264 V	170 ... 264 V
  Wide-range input		No	No
  Overvoltage resistance		2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms
  Mains buffering at Iout rated, min.		20 ms; at Vin = 93/187 V	20 ms; at Vin = 93/187 V
  Rated line frequency 1		50 Hz	50 Hz
  Rated line frequency 2		60 Hz	60 Hz
  Rated line range		45 ... 65 Hz	45 ... 65 Hz
  Input current
  ● at rated input voltage 120 V		1.4 A	3.7 A
  ● at rated input voltage 230 V		0.8 A	1.7 A
  Switch-on current limiting (+25 °C), max.		23 A	62 A
  Duration of inrush current limiting at 25 °C
  ● maximum		3 ms	3 ms
  I²t, max.		1.3 A²·s	12 A²·s
  Built-in incoming fuse		T 3,15 A/250 V (not accessible)	T 6.3 A/250 V (not accessible)
  Protection in the mains power input (IEC 898)		Recommended miniature circuit breaker: 10 A characteristic B or 6 A characteristic C	Recommended miniature circuit breaker: 16 A characteristic B or 10 A characteristic C
  Output
  Output		Controlled, isolated DC voltage	Controlled, isolated DC voltage
  Rated voltage Vout DC		24 V	24 V
  Total tolerance, static ±		1 %	1 %
  Static mains compensation, approx.		0.1 %	0.1 %
  Static load balancing, approx.		0.1 %	0.1 %
  Residual ripple peak-peak, max.		50 mV	50 mV
  Spikes peak-peak, max. (bandwidth: 20 MHz)		150 mV	150 mV
  Product function Output voltage adjustable		No	No
  Status display		LED green for 24 V OK; LED red for error; LED yellow for stand-by	LED green for 24 V OK; LED red for error; LED yellow for stand-by
  On/off behavior		No overshoot of Vout (soft start)	No overshoot of Vout (soft start)
  Startup delay, max.		1.5 s	1.5 s
  Voltage rise, typ.		10 ms	10 ms
  Rated current value Iout rated		3 A	8 A
  Current range		0 ... 3 A	0 ... 8 A
  Supplied active power typical		72 W	192 W
  Short-term overload current
  ● on short-circuiting during the start-up typical		12 A	35 A
  ● at short-circuit during operation typical		12 A	35 A
  Duration of overloading capability for excess current
  ● on short-circuiting during the start-up		70 ms	70 ms
  ● at short-circuit during operation		70 ms	70 ms
  Parallel switching for enhanced performance		No	No
  Efficiency
  Efficiency at Vout rated, Iout rated, approx.		87 %	90 %
  Power loss at Vout rated, Iout rated, approx.		11 W	21 W
  Closed-loop control
  Dynamic mains compensation (Vin rated ±15 %), max.		0.1 %	0.1 %
  Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ.		1 %	2 %
  Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.		3 %	3 %
  Load step setting time 10 to 90%, typ.		5 ms	5 ms
  Load step setting time 90 to 10%, typ.		5 ms	5 ms
  Setting time maximum		5 ms	5 ms
  Protection and monitoring
  Output overvoltage protection		Additional control loop, limitation (closed loop control) at < 28.8 V	Additional control loop, limitation (closed loop control) at < 28.8 V
  Current limitation		3.15 ... 3.6 A	8.4 ... 9.6 A
  Current limitation, typ.		3.4 A	9 A
  Property of the output Short-circuit proof		Yes	Yes
  Short-circuit protection		Electronic shutdown, automatic restart	Electronic shutdown, automatic restart
  Overload/short-circuit indicator		-	-
  Safety
  Primary/secondary isolation		Yes	Yes
  Galvanic isolation		Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 and EN 61131-2	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 and EN 61131-2
  Protection class		Class I	Class I
  Leakage current
  ● maximum		3.5 mA	3.5 mA
  ● typical		0.4 mA	1.3 mA
  CE mark		Yes	Yes
  UL/cUL (CSA) approval		cULus-Listed (UL 508, CSA C22.2 No. 142), File E143289	cULus-Listed (UL 508, CSA C22.2 No. 142), File E143289
  Explosion protection		IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cULus (ISA 12.12.01, CSA C22.2 No.213) Class I, Div. 2, Group ABCD, T4, File E330455	IECEx Ex nA nC IIC T3 Gc; ATEX (EX) II 3G Ex nA nC IIC T3 Gc; cULus (ISA 12.12.01, CSA C22.2 No.213) Class I, Div. 2, Group ABCD, T3, File E330455
  FM approval		Class I, Div. 2, Group ABCD, T4	Class I, Div. 2, Group ABCD, T4
  CB approval		Yes	Yes
  Marine approval		GL, ABS, BV, DNV	GL, ABS, BV, DNV
  Degree of protection (EN 60529)		IP20	IP20
  EMC
  Emitted interference		EN 55022 Class B	EN 55022 Class B
  Supply harmonics limitation		EN 61000-3-2	EN 61000-3-2
  Noise immunity		EN 61000-6-2	EN 61000-6-2
  Operating data
  Ambient temperature
  ● during operation		0 ... 60 °C	0 ... 60 °C
  — Note		with natural convection	with natural convection
  ● during transport		-40 ... +85 °C	-40 ... +85 °C
  ● during storage		-40 ... +85 °C	-40 ... +85 °C
  Humidity class according to EN 60721		Climate class 3K3, no condensation	Climate class 3K3, no condensation
  Mechanics
  Connection technology		Screw-/spring clamp connection	Screw-/spring clamp connection
  Connections
  ● Supply input		L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm²	L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm²
  ● Output		L+, M: 2 spring-loaded terminals each for 0.5 to 2.5 mm²	L+, M: 2 spring-loaded terminals each for 0.5 to 2.5 mm²
  Product function
  ● removable terminal at input		Yes	Yes
  ● removable terminal at output		Yes	Yes
  Width of the enclosure		50 mm	75 mm
  Height of the enclosure		147 mm	147 mm
  Depth of the enclosure		129 mm	129 mm
  Required spacing
  ● top		50 mm
  ● bottom		50 mm
  ● left		0 mm
  ● right		0 mm
  Weight, approx.		0.45 kg	0.74 kg
  Product feature of the enclosure housing for side-by-side mounting		Yes	Yes
  Installation		Can be mounted onto S7-1500 rail	Can be mounted onto S7-1500 rail
  MTBF at 40 °C		1 611 993 h	1 362 918 h
  Other information		Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

  
  

  Дополнительно

  Power connector	6ES7590-8AA00-0AA0
  With coding element for power supply module; spare part, 10 units per packaging unit