SIPLUS extreme RAIL analog output modules

• Заказные данные
  (1)
• Информационные материалы

  Информационные материалы

  • 4-channel analog output module
  • Approved in accordance with the railway standards EN 50155, EN 15121, EN 50124, EN 50125 and EN 45545 for use in rail traffic
  • Optionally with extremely short conversion times
  • For connecting analog actuators without additional amplifiers
  • Even solves more complex automation tasks

  Область применения

  Analog output modules convert a 16-bit digital value into a current or a voltage and output this to the process. They are suitable, for example, for controlling proportional valves or small servo drives.

  Дизайн

  • Installation on the S7-1500 mounting rail using one single screw
  • Standardized 40-pin front connector using screw terminal or push-in technology
  • Connectable core cross-sections: 0.25 mm² to 1.5 mm² (AWG24 to 16), regardless of the front connector used
  • Front connector can be set to prewiring position
  • Front flap with expandable cable compartment, even if fully wired
  • Integrated shielding concept
  • Unambiguous labeling on front of module:
    • Module type
    • Article No.
    • Hardware and firmware version
    • Channel numbers labeling
    • Cabling diagram

  Included in the scope of delivery:

  • Infeed element, shield clamp, and shield terminal
  • One labeling strip for manual labeling
  • One U connector
  • Printed front door

  Функции

  • Uniform display and diagnostics concept:
    • Module status display for ERROR (red LED) and RUN (green LED)
    • Channel status display (channel activated or deactivated, green LED) or diagnostics display (red LED)
    • Display for monitoring the 24 V DC supply voltage (green LED)
  • Supported functions:
    • Consistently high resolution of 16 bits
    • Identification and maintenance data IM0 to IM3
    • Firmware update
    • Channel-specific parameter assignment
    • Channel-granular diagnostics (depends on measurement type/measuring range)
    • Substitute values can be parameterized for the outputs
    • Calibration during runtime
    • Isochronous mode (dependent on the module)

  Технические данные

  Order number		6AG2532-5HD00-1AB0
  		SIPLUS S7-1500 AQ 4xU/I ST T1 RAIL
  General information
  Product type designation		AQ 4xU/I ST
  Product function
  ● I&M data		Yes; I&M0 to I&M3
  CiR – Configuration in RUN
  Reparameterization possible in RUN		Yes
  Calibration possible in RUN		Yes
  Supply voltage
  Type of supply voltage		DC
  Rated value (DC)		24 V
  Analog outputs
  Number of analog outputs		4; > +60 °C max. 4x ±10 V permissible
  Cycle time (all channels), min.		3.2 ms; independent of number of activated channels
  Output ranges, voltage
  ● 0 to 10 V		Yes
  ● 1 V to 5 V		Yes
  ● -10 V to +10 V		Yes
  Output ranges, current
  ● 0 to 20 mA		Yes
  ● -20 mA to +20 mA		Yes
  ● 4 mA to 20 mA		Yes
  Connection of actuators
  ● for voltage output two-wire connection		Yes
  ● for voltage output four-wire connection		Yes
  ● for current output two-wire connection		Yes
  Load impedance (in rated range of output)
  ● with voltage outputs, min.		1 kΩ; 0.5 kOhm at 1 to 5 V
  ● with voltage outputs, capacitive load, max.		1 µF
  ● with current outputs, max.		750 Ω
  ● with current outputs, inductive load, max.		10 mH
  Errors/accuracies
  Basic error limit (operational limit at 25 °C)
  ● Voltage, relative to output range, (+/-)		0.2 %
  ● Current, relative to output range, (+/-)		0.2 %
  Interrupts/diagnostics/status information
  Diagnostics function		Yes
  Substitute values connectable		Yes
  Alarms
  ● Diagnostic alarm		Yes
  Diagnostic messages
  ● Monitoring the supply voltage		Yes
  ● Wire-break		Yes; Only for output type "current"
  ● Short-circuit		Yes; Only for output type "voltage"
  ● Overflow/underflow		Yes
  Diagnostics indication LED
  ● RUN LED		Yes; Green LED
  ● ERROR LED		Yes; Red LED
  ● Monitoring of the supply voltage (PWR-LED)		Yes; Green LED
  ● Channel status display		Yes; Green LED
  ● for channel diagnostics		Yes; Red LED
  ● for module diagnostics		Yes; Red LED
  Potential separation
  Potential separation channels
  ● between the channels and backplane bus		Yes
  Isolation
  Isolation tested with		707 V DC (type test) and according to EN 50155 (routine test)
  Standards, approvals, certificates
  Railway application
  ● EN 50121-3-2		Yes; EMC for rail vehicles
  ● EN 50121-4		Yes; EMC for signal and telecommunications systems
  ● EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
  ● EN 50125-1		Yes; Rail vehicles - see ambient conditions
  ● EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions
  ● EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
  ● EN 50155		Yes; Rail vehicles - temperature class T1, horizontal mounting position, salt spray Class ST2
  ● EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
  ● Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request
  Ambient conditions
  Ambient temperature during operation
  ● horizontal installation, min.		-40 °C; = Tmin; Startup @ -25 °C
  ● horizontal installation, max.		70 °C; = Tmax; > +60 °C max. 4x ±10 V permissible
  Extended ambient conditions
  ● relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
  Relative humidity
  — With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
  Resistance
  — against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
  — against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
  — against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
  — against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
  — against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
  — against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
  Decentralized operation
  Fast Startup supported		Yes; 500 ms
  Dimensions
  Width		35 mm
  Height		147 mm
  Depth		129 mm
  Weights
  Weight, approx.		310 g
  Other
  Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776